Archive for September, 2007

1907 Indian Head Eagle - No Motto w/Periods

Photos used with permission and courtesy of Stacks Auctions

Description:

The original coinage of the 1907 with wire rim on the obverse and with periods after the legend on the reverse is not known, as at the time games were being played at the Mint. Contemporary figures vary slightly, but the numbers of 500 to 550 are often cited, 500 now being the favorite. The truth will not be known unless someone uncovers some long-hidden records (if indeed records were kept to begin with).

Today we estimate that perhaps 325 to 375 exist. All have semi-lustrous surfaces, a hybrid finish between matte and mint frost. The beauty of this particular variety is perhaps best stated by quoting Walter Breen in his 1988 Encyclopedia: "The very first of these [the wire rim issue] are the only available gold $10s showing the Saint-Gaudens' conception in anywhere near their pristine splendor." All specimens are from the same pair of dies, and under magnification there will be seen a multitude of tiny swirls or raised die finish lines. The motif differs from the circulation issue in that there are raised periods before and after the reverse inscriptions. On the Wire Rim version, the rim is raised or sharp, more appropriately called a wire rim, but sometimes called a wire edge. The term "knife rim" or "knife edge" is occasionally used, including in some early listings, and later by Walter Breen. In the past some of these have been called Proof, but as all are from the same dies this point can be debated. They are all Mint State, or they are all Proofs.

Some extensive discussion has taken place about this in the past, including by David Akers in his illustrious study of the series, and in the 1982 Eliasberg catalogue. Perhaps answering the question, the Guide Book doesn't list Proofs at all. However, precisely the same situation rears its head with the next issue, the rolled or rounded rim.

The history of this piece is extensive, rich, and interesting. While these pieces have sometimes been called patterns, an examination of the situation leaves no room for any conclusion except that these were "special" coins produced not at all as patterns, but distributed in small numbers for the profit of Mint employees and favored others with "connections."

On the other hand, to qualify as a pattern, a coin would be a design proposal made in small numbers to test a motif, often involving adjustments made by the engraver before the coins are struck for circulation. In the present instance, these "special" 1907 coins with wire rim and with periods on the reverse were placed in the hands of those who were free to keep them as souvenirs or sell them at a profit.

In order to take advantage of the numismatic trade, such pieces were filtered out of the Mint into the hands of receptive coin dealers, most prominently Henry Chapman of Philadelphia and Thomas L. Elder of New York City, both of whom had quantities on hand for years afterward and regularly offered them in their catalogues.

The portrait is said to have been modeled after Henrietta (Hettie) Anderson, and also used by Saint-Gaudens on a sculpture portrait bust. The reverse is a standing eagle adapted by Saint-Gaudens from that used on the inaugural medal created for Theodore Roosevelt in 1905.

Specifications:

Designer: Augustus Saint-Gaudens
Mintage: 542 Wire Rim (70 Melted in 1914-15) 32,500 Rolled Rim (all but 50 melted)
Denomintion: $10.00
Diameter: ±26.8 millimeters
Metal content: 90% Gold - 10% Copper
Weight: ±258 grains (±16.7 grams)
Varieties:
Wire Rim and Rolled Rim

Additional Resources :

Last Updated : 09/22/2007

1793 Flowing Hair Half Cent

Photos used with permission and courtesy of Heritage Auction Galleries

Description:

The 1793 Liberty Cap has obvious significance as the first Half Cent produced by the Mint, and is also a highly coveted one-year type. In the informative Encyclopedia of United States Half Cents: 1793-1857 Breen wrote that the Philadelphia Mint prepared two obverse and three reverse dies for this issue between April and July, 1793.

The obverse design may have been based on sketches prepared by David Rittenhouse, who in turn relied heavily on Augustin Dupre’s attractive Libertas Americana medal of 1782.

Walter Breen made a case for Adam Eckfeldt as the designer of these coins, although other specialists have disputed such an attribution. It is not known who actually prepared the design and the dies for these first half cents, although it may have been Joseph Wright, who designed the Liberty Cap large cents two months later.

At the time, half cents and large cents were not actually legal tender issues, a status reserved for silver and gold coins that were first produced in the following year. Section 16 of the Mint Act of April 2, 1792 specifically stated: “That all the gold and silver coins which shall have been struck at, and issued from the said mint, shall be a lawful tender in all payments whatsoever, those of full weight according to the respective values herein before declared, and those of less than full weight at values proportional to their respective weights.”

On July 20, the first 7,000 pieces were produced, followed by 24,934 coins on July 26, and a further 3,400 pieces on September 18. These three deliveries totaled a mere 35,334 coins.

Varieties
Four varieties are known for the 1793 half cents, and they were produced in an unbroken chain consisting of two obverse and three reverse dies.

C-1 variety is considered by most specialists to be the first 1793 half cent struck, according to die state and emission sequence analysis. Periods after AMERICA and CENT.

C-2 The cap is far from the Y of LIBERTY, and the 1 numerator is centered over the 200 denominator.

C-3 This variety is most easily attributable by the fraction that is crowded between the ribbons on the reverse, the short 7 in the date, and the low L above the hair.

C-4 The most frequently seen of the 1793 varieties, and characterized by the long stems on the lower reverse and the ribbon ends that are split for at least half their length. It also has a mint-made die lump centered above the 7 in the date. The AT and ES in STATES are widely spaced.

Specifications:

Designer: undetermined; possible candidates include Joseph Wright or Adam Eckfeld
Mintage: 35,334
Denomintion: Half Cent 1/200
Diameter: ±22 millimeters
Metal content: 100% Copper
Weight: 104 grains (6.74 grams)
Edge: Lettered (”TWO HUNDRED FOR A DOLLAR”)

Additional Resources :

Last Updated : 09/22/2007

DISCLAIMER: All content within CoinLink is presented for informational purposes only, with no guarantee of accuracy.
CoinLink does not buy or sell coins or numismatic material, and has no ownership interest in any web site listed within CoinLink.
All News and Article links are direct, without framing, to the original source, which is solely responsible for the content.
No endorsement or affiliation to or from CoinLink is made.